01/14 DIY

DIY Leather Loop Keychain

DIY Leather loop keychainI’ve been meaning to do another leather DIY after how much I loved my first encounter with the stuff, but even better about this one is that it was boyfriend requested!  Just a simple and sleek leather keychain to help carry around keys.  Happy to do it, sir.  I was already feeling inspired by these key rings from The Everygirl, so it was meant to be.

I actually made three, but the first one was a complete disaster because I was rushing to beat sundown (blogger. problems.) so I’ll share a couple morsels of cautionary tips as I go on with the instructions.  In general though, this is a fairly simple DIY and a great beginner project for anyone wanting to get into leather crafting.

Materials:
tooling leather
ruler
rotary cutter
X-ACTO knife
leather awl
leather punch (Kind of.  I’ll explain this in the steps.)
rivet kit
key ring

Leather measurementsHere are the rough measurements for the leather piece.  I used a rotary cutter and ruler to cut off a one inch wide strip, then used a pencil to draw out the little trapezoid shaped cut-outs shown above.  Those smaller pieces were cut with an X-ACTO knife, and was probably the most difficult part.  Getting those corners cut clean takes patience, guys.

Mistake #1: I didn’t think at all at first about how long I wanted the loop to be so I just left it the length that it was, only to find out later that it was awkwardly long.  The next time around I measured and cut the loop length to 6″ as marked above, but the actual leather in the photos of all the steps is longer, so just an FYI for anyone that was detailed enough to notice that it didn’t look like 6″.  Anyone?

FoldingThe trapezoid cut-outs are there to make a thinner loop for the key ring to go, which becomes more obvious when folding the short end over, then the long end over on top.  This is how the leather strap will be constructed.

AwlSo this part is a little weird.  I already had this leather awl and thought it would be enough to poke a hole big enough for the rivets, but it wasn’t.  This is where I want to say that it’s best to use a leather punch for the holes after first marking where they should go, then to punch out a hole in each layer of the leather.  Buuuuuut if you’re like me and want to avoid getting a leather punch, I improvised by poking the awl through all three layers of leather, then enlarging each hole by sticking an X-ACTO knife through in a cross formation.  It isn’t neat and it’s a bit tricky, but it worked.  Just need to be careful not to push the knife too far into the hole or else it will cut a slit that’s too big (Mistake #2 from my first time around).

RivetsThe best part.  Have you used rivets for anything?  They’re amazing, and this rivet kit is spectacular.  After slipping the key ring through and pushing the rivet backing through the holes, I hammered the rivet shut.

Mistake #3: Maybe it was the adrenaline from rushing, but for the first keychain I made, I bashed the life out of the rivet.  This somehow misaligned the top and bottom and it shut diagonally and off-center, which wasn’t cute at all.  Bashing is completely unnecessary.  Light taps with the hammer are sufficient, and you can go progressively harder if needed, but not too hard.  

back side of keychainHere’s the back side of the keychain.  SO satisfying to see how good the rivet shut.  I sincerely hope you’ll soon know what that joy feels like if you don’t already.

DIY Leather Loop Keychain

Leather loop keychains DIY

Black leather loop keychain DIYOne for him.

Natural leather loop keychain DIYOne for me!

DIY black and natural leather loop keychainsI’ve totally been in this kind of color mood lately, namely no color.  Is it the winter?  Neutrals are a favorite forever, but just even more so lately.  Also, I guess tooling leather only comes in so many colors, ha!  Boyfriend initially requested brown, but I couldn’t even find that.  Poor him.  Which of these two colors do you prefer?

20 comments on “DIY Leather Loop Keychain”

  1. I’ve been needing a key chain for a while now and I love these! I could totally use my leather stamping kit and put my initials or something fun on it. So cute that you made his and hers :)

    1. I definitely thought about stamping, until I saw the price of the kit, then I decided maybe next time…. haha! Thanks, Bre!

  2. Love these! I know what you mean about rushing to get projects done while there’s natural light! This is the bane of my blogging life at the moment and I’m having to stretch projects out over days so I can photo them before it gets too dark! Roll on the summer! x

    1. Yup! Then talk about if the photos didn’t turn out quiet right and then you need to wait for another day of sunlight to re-shoot. I like to blame the sun for all of my blog frustrations ;) Summer time is definitely more enjoyable.

    1. Thank you! Yea the black is definitely more practical, and one of my favorite colors ever <3 and I love the leather stamper idea!

  3. Hi Amy,
    Thanks for the easy breakdown of the DIY! Super excited to try it out. Where did you purchase your leather? Is there a specific type we need? Possibly one that is flexible and bends easily? Thank you!

    1. Hi Jane! I got the leather from Michaels. I suggest tooling leather. It’s on the sturdier side while still being flexible enough to bend. Thanks for your question! Let me know how it goes :)

  4. I just made this as a gift for my husband. I love the result! Thanks for the well-made tutorial!

Leave a Reply

Your email address will not be published. Required fields are marked *